→ The Lansweeper Customer Excellence Awards 2024 - Submit Your Project Now! Learn More & Enter Here

cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Nichamon
Engaged Sweeper II

Hi,

I have Cisco Access Point that managed by WLC (Lansweeper can scan WLC which) but Lansweeper can not scan access point. I have try Devices Tester and it shown 

Scanning SSH..
SSH server: SSH-2.0-OpenSSH_8.5
System info: can't get tty settingscan't set orig mode
Hostname: can't get tty settingscan't set orig mode
Kernel name: can't get tty settingscan't set orig mode
Kernel release: can't get tty settingscan't set orig mode
Kernel version: can't get tty settingscan't set orig mode
Processors: can't get tty settingscan't set orig mode
VMware product name: can't get tty settingscan't set orig mode
VMware vendor name: can't get tty settingscan't set orig mode
Disks: can't get tty settingscan't set orig mode
Network: can't get tty settingscan't set orig mode

Already have config SSH credentials and map credential and targets.

13 REPLIES 13
Brown_Dog_NG
Champion Sweeper

If the Cisco APs are joined to a WLC, you can only poll the WLC for SNMP queries regarding the APs. The APs are set to forward SNMP to the WLC per Cisco. I'll have to dig through the documentation again, but the documentation does exist from Cisco.

-Don't forget to hand out Kudos and mark Solutions to replies you receive!-
LS Tech Support Email: Support@lansweeper.com
LS Tech Support KB: https://www.lansweeper.com/contact-support/

Below are two community discussions stating that you must poll the WLC and not the APs.

https://community.cisco.com/t5/wireless/snmp-on-wlc-ap-s/td-p/4127662

 

https://community.cisco.com/t5/wireless/snmp-config-on-access-point-through-controller/td-p/3019784

 

-Don't forget to hand out Kudos and mark Solutions to replies you receive!-
LS Tech Support Email: Support@lansweeper.com
LS Tech Support KB: https://www.lansweeper.com/contact-support/

I have config SNMP community and trap reciver if I understand correctly that's no SNMP on Access Point. WLC that owner SNMP. Look like WLC cann't reply result of specific OID.

What model WLC are you using? The SNMPWalk is certainly a good starting point. You can attempt to dig through the MIBs provided by Ciscos Website and attempt to identify what you're needing from that. I personally was overwhelmed by the information available but it can be learned with time and effort.

AireOS 3504 WLC - This Cisco link has some OIDs listed that may be useful.

Paessler SNMP Tester - Here is a useful SNMP Tool you can leverage if Lansweeper Device Tester is not your preference.

Cisco Forum - Here is a Community Post that contains 2 MIBs that may prove useful for you.

Cisco MIB Navigator - Here is the MIB Navigator for Cisco that you should use to investigate and test further.

-Don't forget to hand out Kudos and mark Solutions to replies you receive!-
LS Tech Support Email: Support@lansweeper.com
LS Tech Support KB: https://www.lansweeper.com/contact-support/

Hi, My WLC is CT2504 and CAP3602. Maybe CAP3602 is not support for snmp, I have investigate that in navigator.

Nichamon
Engaged Sweeper II

I have try many custom by OID on WLC but it didn't work. Look like result is invalid value. I have try OID Number of Connected Clients: 1.3.6.1.4.1.9.9.618.1.8.12.0 that's work but bsn apserial number: 1.3.6.1.4.1.14179.2.2.1.1.17 is null value. Am I use OID to scan Serial Number of APs on AP or WLC?

Thank you for reply. Yes, Already read Scan extra SNMP data but I have no idea which OID can get the result that I need.

Did you try SNMP_WALK in MIB Browser?

https://ireasoning.com/mibbrowser.shtml for example