IP4 not IP6

[Marc_Tobien]

HI
I am having problems to create an asset list with


Assetname
RAM in GB
Memory in GB
Disk in GB
Manufacturer
Model
OSname
IP4 Adresse which have now a ping respond ( switcht on)

I can get IP Adresse but then I get also the IP 6 Adresse and in the moment I am delinting ist in excel by hand.
there must by a way to set a filter for IP4. IP numeric is not good because then I have to reconvert it in excel to IP format
Thank you

[Marc_Tobien]

THX RC62N
I found the IP addresses in the tblAssets and that works fine for me.
Do you know if there is a way to list only active IP addresses of PCs and servers that are running when I run the report? We always scan late at night to keep the load low?
I then filter in Excel the date of last seen

[RCorbeil]

You don't specify which IP address source you're trying to use. If it's tblAssets, as Andy.S's example offers, tlAssets.IPAddress should be the IPv4 address in normal dotted-quad format.

Since you also refer to IP addresses including the IPv6 address, I assume you're also pulling form tblNetwork. If so, from my inventory, where tblNetwork.IPAddress includes both IPv4 and IPv6 addresses, it's formatted either "IPv4 - IPv6" or "IPv4 , IPv6". Either way, there's a space after the IPv4 address that can be sought as a separator.

CASE
  WHEN CharIndex(' ', tblNetwork.IPAddress) > 0
  THEN Left(tblNetwork.IPAddress, CharIndex(' ', tblNetwork.IPAddress)-1)
  ELSE tblNetwork.IPAddress
END AS IPv4Address

[Andy_Sismey]

Have a look at this thread , it gives you 85% of what your after :- https://www.lansweeper.com/forum/yaf_postst15067_Total-Space-and-Free-Space.aspx#post51173 , you just need to add the memory count like this :

Select Top 1000000 tblAssets.AssetID,
  tblAssets.AssetName,
  tblAssets.Domain,
  tblAssets.Username,
  tblAssets.Userdomain,
  Coalesce(tsysOS.Image, tsysAssetTypes.AssetTypeIcon16) As icon,
  tblAssets.IPAddress,
  tsysIPLocations.IPLocation,
  tblAssetCustom.Model,
  tblAssetCustom.Manufacturer,
  tsysOS.OSname As OS,
  tblAssets.SP,
  tblAssets.Lastseen,
  tblAssets.Lasttried,
  tblDiskdrives.Caption,
  Cast(Cast(tblDiskdrives.Freespace As bigint) / 1024 / 1024 / 1024 As
  numeric) As FreeGB,
  Cast(Cast(tblDiskdrives.Size As bigint) / 1024 / 1024 / 1024 As numeric) As
  TotalSizeGB,
  Floor(Cast(Cast(tblComputersystem.TotalPhysicalMemory As bigint) / 1024 /
  1024 As numeric)) As [Total Memory],
  tblDiskdrives.Lastchanged
From tblAssets
  Inner Join tblDiskdrives On tblAssets.AssetID = tblDiskdrives.AssetID
  Inner Join tblAssetCustom On tblAssets.AssetID = tblAssetCustom.AssetID
  Inner Join tblState On tblState.State = tblAssetCustom.State
  Inner Join tsysAssetTypes On tsysAssetTypes.AssetType = tblAssets.Assettype
  Inner Join tsysIPLocations On tsysIPLocations.LocationID =
    tblAssets.LocationID
  Left Outer Join tsysOS On tblAssets.OScode = tsysOS.OScode
  Inner Join tblComputersystem On tblAssets.AssetID = tblComputersystem.AssetID
Where Cast(Cast(tblDiskdrives.Size As bigint) / 1024 / 1024 / 1024 As numeric)
  <> 0 And tblState.Statename = 'Active' And tblDiskdrives.DriveType = 3
Order By tblAssets.Domain,
  tblAssets.AssetName,
  tblDiskdrives.Caption

Taken from this thread : https://www.lansweeper.com/forum/yaf_postst4172_Change-the-memeory-size-in-reports-to-MB.aspx#post19639