
Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:08 PM
All computers in my untrusted domain get "Wmierror: Access is denied 0x80070005"
I think I followed http://www.lansweeper.com/kb/untrusted.aspx precisely.
Even the connection tester gives all "OK"
DNS test
-----------------------------------------------
Is this the correct remote IP: 172.31.210.12
If not, please check for DNS problems
Is this the correct computer name: SERVER001
If not, please check for DNS problems
Remote WMI test
-----------------------------------------------
Found: Microsoft(R) Windows(R) Server 2003 Enterprise x64 Edition Service Pack 2
\root\cimv2 Remote WMI access test OK
Remote Registry test using WMI
-----------------------------------------------
Found: Microsoft Windows Server 2003 R2 Service Pack 2
\root\default Remote WMI access test OK
I think I followed http://www.lansweeper.com/kb/untrusted.aspx precisely.
Even the connection tester gives all "OK"
DNS test
-----------------------------------------------
Is this the correct remote IP: 172.31.210.12
If not, please check for DNS problems
Is this the correct computer name: SERVER001
If not, please check for DNS problems
Remote WMI test
-----------------------------------------------
Found: Microsoft(R) Windows(R) Server 2003 Enterprise x64 Edition Service Pack 2
\root\cimv2 Remote WMI access test OK
Remote Registry test using WMI
-----------------------------------------------
Found: Microsoft Windows Server 2003 R2 Service Pack 2
\root\default Remote WMI access test OK
Labels:
- Labels:
-
Archive
7 REPLIES 7

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-13-2010 10:57 AM
The config is refreshed every 15 minutes so it's normal because the credentials aren't used yet.

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:24 PM
There are two domains. I have enabled IP scanning for the primary domain for VPN users and network devices. I hadn't enabled IP Scanning for my test domain. I just added it as I was seeing the errors.
I trigger scanned them all and I am all good.
So is the error typical within the first 15 minutes?
I trigger scanned them all and I am all good.
So is the error typical within the first 15 minutes?

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:15 PM
So did I need to add my untrusted domain to "IP Scanning" at all? And is it normal to see these errors in the 15 minute span of time?

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:18 PM
NorthH wrote:
So did I need to add my untrusted domain to "IP Scanning" at all? And is it normal to see these errors in the 15 minute span of time?
Do you use ip scanning for this domain?
If yes, you need to add the domain netbios name.

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:14 PM
It can take up to 15 minutes for the settings to be active.

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:13 PM
2 out of 6 shows me data (like disk space and event logs etc...)and those 2 still have the same error in the Error Tab. Is this normal?

Options
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
‎05-12-2010 10:10 PM
I dont think I waited long enough... Now I see a few starting to work. I also added the IP range/Netbios name to IP Scanning. Was this the difference?
